Updated November 2026

Pairing Xiaomi bone conduction headphones takes about a minute once you know the sequence: put the earphones into pairing mode, enable Bluetooth on your phone, and select the device from the list. This guide walks through that process, explains how to tell when pairing mode is active, and covers the fixes that solve most connection failures.

What You Need Before You Start

Pairing goes faster when the basics are in place. Check these items first:

Shopping for one? See our guide: AfterShokz Titanium Wireless Bone Conduction Headphones Review (2026).

  • Headphones charged to at least 30 percent, since low battery can stop the pairing indicator from flashing.
  • A phone or tablet with Bluetooth support and the Xiaomi-compatible companion app installed if your model uses one.
  • No other device currently connected to the headphones. Disconnect any active source first.
  • Your phone within about one meter of the headphones during setup.

Model-specific button sequences vary, so check the manual or the official Xiaomi support pages for your exact model before you begin.

How to Put Xiaomi Bone Conduction Headphones in Pairing Mode

Most bone conduction models enter pairing mode when you hold the power or multifunction button for several seconds, until an indicator light flashes or a voice prompt announces that the headphones are ready to pair. Power the headphones off first, then press and hold the button until you see or hear that signal.

Recognizing a Successful Pairing Mode

Listen for the voice prompt or watch for an alternating red and blue or rapid blinking light, depending on the model. If nothing happens after about ten seconds, the headphones are probably still on, so power-cycle them and try again.

How to Connect From Your Phone

  1. Open Settings on your phone and go to Bluetooth.
  2. Turn Bluetooth on and wait for the scan to finish.
  3. Tap the Xiaomi headphone name when it appears in the list of available devices.
  4. Accept the pairing request if prompted. Some phones ask you to confirm a code on both devices.
  5. Wait for the status to show “Connected.” Play a short audio clip to confirm sound is reaching the headphones.

After the first pairing, the headphones usually reconnect automatically whenever they are powered on near the phone.

Fixing Common Pairing Problems

When the headphones do not appear in the Bluetooth list, or they pair but drop out, work through these causes in order. Most issues come down to a stale pairing record or a dead battery rather than a fault in the hardware.

Symptom Likely cause Fix
Headphones not listed Not in pairing mode Hold the button until the indicator or voice prompt appears
Pairs, then disconnects Old pairing record on phone Forget the device on the phone and pair again
Connected but no sound Audio routed to phone speaker Check the audio output selection in your phone’s sound menu
Pairing indicator does not flash Battery too low Charge for at least 15 minutes, then retry

Common Mistakes and Tips

  • Forgetting to disconnect the headphones from another device, which blocks new pairing requests.
  • Pressing the button briefly instead of holding it, which powers the headphones on but does not enter pairing mode.
  • Pairing from a distance. Keep the phone close during setup.
  • Skipping the reset. If repeated attempts fail, try a factory reset as described in your model’s manual.
  • Using a bone conduction fit that is too loose, which can make the sound feel faint and mimic a connection problem.

A few accessories make setup and day-to-day use easier.

  • A short, certified USB charging cable keeps the battery topped up so pairing mode activates reliably. View on Amazon
  • A clear silicone case protects the earhooks and buttons during travel. View on Amazon

FAQ

Why won’t my Xiaomi bone conduction headphones show up in Bluetooth settings?

The headphones are likely not in pairing mode. Power them off, then hold the button until the indicator flashes or a voice prompt plays, and check the list again.

Can I pair Xiaomi bone conduction headphones with two phones at once?

Many models store multiple paired devices but connect to only one active source at a time. Check your model’s manual for multipoint support.

What should I do if the headphones keep disconnecting after pairing?

Forget the device on your phone, charge the headphones fully, and pair again from the start. If the problem continues, contact Xiaomi support for guidance.

Conclusion

To pair Xiaomi bone conduction headphones, put them in pairing mode with a long button press, then select them from your phone’s Bluetooth list. Most failed attempts trace back to a low battery, an old pairing record, or the headphones not being in the right mode. Work through those checks and the connection usually succeeds on the next try.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our headphone tech & types guides, checking product details against manufacturer specifications and owner feedback.