Updated November 2026
To pair AfterShokz bone conduction headphones, you put the headset into pairing mode, then select it from the Bluetooth list on your phone, tablet or computer. The whole process usually takes under a minute. This guide walks through each step and covers what to do when the pairing doesn’t go through.
Before You Start
Pairing works best when the headphones have enough charge and your device is close by. Gather the following before you begin:
Shopping for one? See our guide: AfterShokz Titanium Wireless Bone Conduction Headphones Review (2026).
- Your AfterShokz headphones, charged to at least a quarter. Use the USB cable supplied with the headset.
- Your phone, tablet or laptop with Bluetooth turned on.
- The headphones within about three feet of the device during setup.
- No other Bluetooth headset paired to the same device, which can cause confusion in the device list.
How to Put AfterShokz Headphones Into Pairing Mode
Most AfterShokz models enter pairing mode the same way. Power the headphones off first, then press and hold the power button until you hear a voice prompt or see an indicator light flash in alternating colors, usually red and blue. The exact button press and light pattern vary by model, so check the quick start guide included in the box or on the official AfterShokz support page if the pattern doesn’t match.
If the headphones have been paired before and won’t enter pairing mode, clear the old connection first. Hold the power and volume-down buttons together for several seconds until the status light changes. This resets the Bluetooth memory on most models.
Connecting to Your Phone, Tablet or Computer
On an iPhone or iPad
- Open Settings and tap Bluetooth.
- Wait for the headphones to appear under Other Devices.
- Tap the model name to connect.
On an Android phone
- Open Settings, then Connected devices or Bluetooth, depending on your version.
- Tap Pair new device and select the headphones from the list.
- Confirm the pairing if prompted.
On a Windows or Mac computer
On Windows, open Settings, go to Bluetooth & devices, and select Add device. On a Mac, open System Settings, choose Bluetooth, and click Connect next to the headphones. In both cases, make sure the headset is in pairing mode first.
Confirm the Connection and Test Audio
Once paired, the device list should show the headphones as connected. Play a short audio clip and adjust the volume on the headset itself. If sound comes from your phone’s speaker instead, open your audio output menu and choose the AfterShokz model manually.
After the first pairing, the headphones usually reconnect automatically when you power them on near the same device. You only need to repeat these steps if you switch to a new phone or clear the Bluetooth memory.
Common Mistakes
- Trying to pair while the headphones are still powered on and connected to another device. Turn them off first.
- Searching for the headphones before they enter pairing mode, so they never appear in the list.
- Keeping the headset too far from the device during setup. Stay within a few feet.
- Forgetting to check the audio output setting after pairing, which leaves sound playing from the phone speaker.
- Assuming every model uses the same button sequence. Check your specific model’s guide.
Recommended Gear
- A spare USB charging cable. Keeping a second cable at your desk or in your bag makes it easier to charge before pairing. View on Amazon
- A small carrying case. A hard case protects the headset from scratches and keeps the cable from tangling in your bag. View on Amazon
FAQ
Why won’t my AfterShokz headphones show up in the Bluetooth list?
The headphones are most likely not in pairing mode, or they are still connected to another device. Turn them off, reset them, and try the pairing steps again with the headset close to your device.
Can I pair AfterShokz headphones with two devices at once?
Some models support multipoint connection to two devices, while others connect to only one at a time. Check the specifications for your exact model before relying on this feature.
What should I do if the headphones paired but there is no sound?
Set your device’s audio output to the AfterShokz model, raise the volume on both the phone and the headset, and confirm the headset is powered on. If the problem continues, restart the device and reconnect.
Conclusion
Pairing AfterShokz bone conduction headphones takes a few steps: charge the headset, enter pairing mode, and select it from your device’s Bluetooth menu. Once connected, they generally reconnect on their own. If you run into trouble, a full reset and a check of your audio output setting solve most problems.
