Updated November 2026

To change the Bluetooth codec on a Samsung Galaxy phone, you open Developer options, find the Bluetooth audio codec setting, and select the codec your headphones support. This guide walks through each step, explains which codecs Galaxy phones offer, and shows how to confirm the change took effect. Most users only need a few minutes and no extra apps.

Before You Start: Check Your Phone and Headphones

Codec options depend on both devices. Your Galaxy phone can only use codecs its chipset and software support, and your headphones or speaker can only use codecs they were built for. If both sides share a codec, your phone will negotiate the better one automatically. If they share none, the connection falls back to SBC, the baseline codec every Bluetooth device supports.

Shopping for one? See our guide: Samsung S22 Ultra Bluetooth Codec Review: Features and Performance.

Check your headphone manual or the manufacturer’s spec sheet for listed codecs such as AAC, aptX, aptX HD, or LDAC. Samsung’s own Galaxy phones typically support SBC, AAC, and LDAC, with some models also offering aptX variants depending on region and firmware.

How to Change the Bluetooth Codec on a Galaxy Phone

Changing the codec is a developer setting, so you need to unlock Developer options first. Samsung hides this menu by default.

  1. Open Settings and tap About phone, then Software information.
  2. Tap Build number seven times until you see a message confirming Developer mode is on.
  3. Go back to the main Settings screen and open Developer options. On some One UI versions it sits under Settings > General management.
  4. Scroll to the Bluetooth section and tap Bluetooth Audio Codec.
  5. Choose the codec you want, such as LDAC or AAC, and return to the previous screen.

Reconnect and Confirm the Change

A codec change applies to the next connection, so disconnect your headphones first. Turn Bluetooth off and on, or use the Bluetooth quick toggle, then reconnect. Return to Developer options and check that the selected codec now shows as active. If the active codec still reads SBC, the headphones likely do not support your chosen codec.

Set the Sample Rate and Bits Per Sample

Some Samsung builds let you adjust sample rate and bits per sample under the same Bluetooth audio menu. Higher values can improve detail with codecs like LDAC, but they also increase bandwidth use. If audio stutters, drop back to the default values before changing the codec itself.

Choosing the Right Codec

Pick a codec based on what matters most to you. The table below summarizes common tradeoffs.

Codec Best for Typical tradeoff
SBC Universal compatibility Lowest audio detail
AAC iPhone and Samsung pairings Quality varies by encoder
aptX / aptX HD Android devices with matching support Needs both sides to support it
LDAC Maximum detail on compatible headphones Can drop out at range or in crowded RF environments

If you game or watch video, latency matters more than fidelity. For that case, see Which Bluetooth Codec for Gaming Gives You the Lowest Lag? Users looking for a broader overview of trade-offs can read Does Bluetooth Codec Matter? What Changes in Sound Quality (2026).

Common Mistakes and Tips

  • Forgetting to reconnect after changing the codec. The new setting does not apply to an active connection.
  • Choosing LDAC and expecting a lossless signal. Bluetooth still compresses audio, and results depend on the headphones.
  • Leaving Developer options on with unrelated settings changed. Turn off options you do not use to avoid confusion.
  • Assuming the codec menu is missing from your phone. Check One UI version and region, since availability varies.
  • Ignoring signal range. Higher-bitrate codecs are more sensitive to interference, so stay close to the phone.

Troubleshooting Codec Changes That Do Not Stick

If the codec reverts after each reconnect, the headphones may be requesting a different codec during pairing. Forget the device in Bluetooth settings, then pair it again with Developer options set to your preferred codec. Users dealing with stubborn cases sometimes find the same steps covered in Bluetooth Audio Codec Won't Change: 6 Fixes That Work (2026).

FAQ

Do I need to root my Samsung phone to change the Bluetooth codec?

No. The Bluetooth audio codec setting is available in standard Developer options on supported Galaxy models, so rooting is not required.

Why don’t I see LDAC in my codec list?

LDAC appears only on phones and firmware versions that include it. Check your model’s specifications or your current One UI version.

Will changing the codec drain my battery faster?

Higher-bitrate codecs can use slightly more power than SBC, though the difference is usually modest. If battery life is a concern, switch back to AAC or SBC.

Conclusion

Changing the Bluetooth codec on a Samsung Galaxy phone takes a few taps in Developer options, plus a reconnect to apply the change. Confirm the active codec after reconnecting, and choose one your headphones actually support. Consult your device manufacturer’s support resources if a codec will not appear or stay selected.

Emily Parker

About Emily Parker

Emily Parker is part of our editorial team and reviews and edits our headphone tech & types guides, checking product details against manufacturer specifications and owner feedback.