Updated November 2026

The JLab Go Air earbuds carry an IP rating that covers sweat and light splashes, which makes them suitable for workouts and rainy walks. They are not built to be submerged, so swimming, showering, or rinsing them under a tap is outside what the rating supports. This guide explains what the rating means, how to use the earbuds around water, and how to clean them without damaging the seals.

What the IP Rating Means for the Go Air

JLab lists an IP rating for the Go Air that indicates protection against dust and water splashes. An IP rating uses two digits: the first describes solid particle protection, and the second describes water resistance. The second digit is the one that matters for sweat and rain. If you want the full breakdown of how these codes are read, see What Do Waterproof Ratings for Earbuds Mean? IP Codes Explained.

Shopping for one? See our guide: 7 Best Sol Republic Amps Air 2.0 Waterproof Wireless Bluetooth Earbuds (2026): Our Picks.

Water resistance at this level means the earbuds can handle moisture from sweat, drizzle, and accidental splashes. It does not mean they can handle pressure from being underwater. Manufacturers that rate earbuds for immersion specify depth and duration; a splash rating does not include either.

How to Use the Go Air Around Water

Use the earbuds safely around water by following these steps:

  1. Confirm the earbuds and case lids are fully closed before exercising outdoors in wet weather.
  2. Wipe the earbuds with a dry cloth after heavy sweating or rain exposure.
  3. Keep the charging case dry at all times. Moisture around the charging contacts can cause corrosion.
  4. Remove the earbuds before entering a shower, pool, lake, or ocean.
  5. Let the earbuds air-dry at room temperature for several hours if they get wet. Do not use heat sources.

Factors That Affect Water Resistance Over Time

A rated seal is only as good as its condition. Several factors reduce protection over time:

  • Ear tip wear: Silicone tips can stretch or harden, which weakens the fit and lets moisture reach the speaker openings.
  • Debris in the charging contacts: Lint, sweat salts, and dirt can block connections or trap moisture.
  • Cracks or damage to the case: A damaged hinge or lid gap lets water into the case compartment.
  • Repeated exposure: Frequent sweating and humidity wear down seals gradually, even when no single event causes damage.

Owners often report that water resistance seems to fade after a year or more of heavy use, which is consistent with normal seal aging. Replacing worn ear tips is a low-cost way to restore a snug fit.

Cleaning the Go Air Without Compromising Seals

Clean the earbuds regularly to keep moisture and sweat residue from building up.

  1. Power off the earbuds and remove the ear tips.
  2. Wipe the earbud bodies and case with a soft, slightly damp cloth.
  3. Clear the speaker mesh with a dry soft brush. Do not press debris deeper into the openings.
  4. Clean the charging contacts on the earbuds and case with a dry cotton swab.
  5. Rinse the ear tips in lukewarm water, dry them fully, and reattach them.

Avoid alcohol-based cleaners, abrasive materials, and compressed air pushed directly into the speaker grilles.

Common Mistakes

  • Assuming an IP rating means the earbuds can be worn in the shower or pool.
  • Charging the earbuds while they are still wet, which can cause contact corrosion.
  • Leaving the case lid open in humid conditions.
  • Ignoring worn or loose ear tips, which weaken both fit and water protection.
  • Using hot air or a hair dryer to speed drying, which can damage internal components.

A few simple accessories help protect the Go Air in wet conditions.

  • Replacement silicone ear tips in multiple sizes: A secure seal keeps sweat out of the speaker openings and helps the earbuds stay in place during workouts. View on Amazon
  • Soft-bristle cleaning brush for earbuds: A dry brush removes lint and debris from speaker mesh without pushing it inward. View on Amazon

FAQ

Can I wear the JLab Go Air earbuds while swimming?

No. The IP rating covers sweat and splashes, not submersion. Remove the earbuds before swimming or entering a pool or shower.

Why did my earbuds stop working after getting wet?

Moisture may be trapped in the speaker openings or charging contacts. Dry the earbuds and case thoroughly, let them air-dry for several hours, and try again once they are completely dry.

How do I know if the seal has worn out?

Signs include loose fit, muffled sound, or moisture appearing inside the case. Inspect the ear tips and replace them if they look stretched, cracked, or hardened.

Conclusion

The JLab Go Air earbuds are water resistant enough for sweat, rain, and splashes, but they are not designed for submersion. Keeping the case dry, cleaning the contacts, and replacing worn ear tips will preserve their protection. For a broader comparison of how JLab models handle water, see Are JLab Earbuds Waterproof? IP Ratings and What They Cover.

Ethan Brooks

About Ethan Brooks

Ethan Brooks is part of our editorial team and reviews and edits our headphone tech & types guides, checking product details against manufacturer specifications and owner feedback.